Skip to Content
Repair

Fault codes Bulex

Type the code your boiler shows: what it means, what you can do, and when a technician is needed.

Sometimes a number follows the code (6A 227): type it too, the page shows what it means.

Your brand

Your boiler Bulex

The model is written on the rating plate, often under the cover.

All codes Bulex

F.00 Flow temperature sensor disconnected
F.01 Return sensor fault or ignition fault
F.03 Cylinder sensor or air supply fault
F.035 Air and flue duct blocked
F.040 Air ratio too low
F.044 Weak flame signal or spillage sensor fault
F.047 Hot water outlet sensor fault
F.078 Accessory or control module misconfigured
F.080 Storage tank inlet sensor fault
F.087 Ignition not connected to the circuit board
F.088 Gas valve not connected
F.089 Heating pump incompatible or badly connected
F.092 Gas type setting not valid
F.095 Gas valve at its minimum limit
F.096 Gas valve at its maximum limit
F.10 Flow sensor short or return sensor fault
F.105 Gas valve setting to be redone
F.11 Return sensor short or display link fault
F.13 Cylinder sensor short or main board fault
F.15 Flue gas sensor short or motor fault
F.194 Circuit board power supply faulty
F.195 Supply voltage too low
F.196 Supply voltage too high
F.20 Overheating or incompatible interface
F.22 Not enough water or pressure too high
F.23 Temperature difference or poor water circulation
F.24 Temperature rising too fast
F.25 Flue gas temperature too high
F.27 Flame detected with the burner off
F.28 Ignition failure or sensor mismatch
F.29 Flame lost during operation, relighting failed
F.317 Hot water flow sensor signal implausible
F.318 Three-way valve does not move
F.32 Fan not running correctly
F.320 Heating pump blocked
F.321 Pump electronics faulty
F.322 Heating pump overheating
F.323 Heating pump running dry
F.324 Pump electrical connection cut
F.325 Heating pump fault
F.326 Two hydraulic components not working
F.327 Hot water circuit not connected or blocked
F.33 Air pressure switch fault
F.34 Safety shutdown by pressure monitoring
F.344 Control electrode unusable
F.346 Hard ignition detected, ignition failed
F.36 Flue system fault
F.363 Display memory error
F.390 Initialisation missing after software update
F.42 Coding resistor fault
F.45 Cold water inlet sensor fault
F.46 Cold water inlet sensor short circuit
F.48 Hot water outlet sensor short circuit
F.49 eBUS line fault (controls)
F.51 Fault detected by the flue gas sensor
F.52 Mass flow sensor not connected
F.53 Gas flow outside expected values
F.54 Gas pressure too low at start-up
F.56 Safety shutdown: CO limit exceeded
F.57 Combustion control fault
F.61 Gas valve control fault
F.62 Delayed gas valve shut-off
F.63 Circuit board memory (EEPROM) fault
F.64 Electronics or sensor fault
F.65 Electronics temperature too high
F.67 Implausible flame signal
F.68 Unstable flame signal
F.70 Invalid boiler identification
F.707 No communication between display and circuit board
F.71 Flow sensor stuck on one value
F.72 Flow and return sensor mismatch
F.73 Water pressure sensor: signal too low
F.74 Water pressure sensor: signal too high
F.75 Pump fault or lack of water
F.77 Flue gas flap or condensate pump fault
F.79 Hot water tank sensor fault
F.81 Storage tank charging failed
F.83 Temperature does not rise at burner start
F.84 Implausible flow-return temperature difference
F.85 Flow and return sensors wrongly fitted
F.86 External safety contact open (underfloor heating)
F.905 Communication interface switched off
F.97 Main circuit board self-test failed
F12 Hot water sensor short or communication fault
F14 Heating water overheating
F16 Flame detection or flow sensor fault
F17 Supply voltage too low
F18 Control interface fault
F19 Flow sensor or water flow detector fault
F2 Hot water sensor or air supply fault
F21 Not enough water in the system
F26 Gas valve fault or temperature difference
F30 Water pressure sensor fault
F4 Flame lost during operation
F43 External flue spillage safety sensor fault
F5 Overheating or flue gas sensor fault
F6 Flow sensor or flue gas sensor fault
F7 Hot water temperature sensor fault
F76 Heat exchanger overheat protection tripped
F8 Cylinder temperature sensor fault
F9 Water pressure sensor fault
I.003 Boiler service due
I.020 Low heating water pressure
I.144 Flame control electrode worn
L.016 Flame lost at minimum power
L.022 Too little water circulating in the heating
L.025 Cold water inlet sensor short-circuited
L.032 Flow sensor faulty or signal implausible
L.095 Gas valve at its lower control limit
L.096 Gas valve at its upper control limit
L.097 Not enough air for combustion
L.105 Boiler air venting not completed
L.144 Flame signal too weak at the control electrode
L.194 Circuit board power supply failing
L.195 Supply voltage too low
L.196 Supply voltage too high
L.319 Boiler internal bypass blocked
L.320 Heating pump blocked
L.322 Pump electronics overheating
N.013 Water pressure sensor signal invalid
N.027 Hot water temperature sensor signal implausible
N.032 Flow sensor faulty or signal implausible
N.089 Heating pump not matching the boiler type
N.095 Gas valve at its lower control limit
N.096 Gas valve at its upper control limit
N.097 Not enough air for combustion
N.100 Outdoor temperature sensor signal lost
N.144 Flame signal too weak at the control electrode
N.194 Circuit board power supply failing
N.317 Hot water flow sensor signal implausible
N.319 Boiler internal bypass blocked
N.324 Pump electrical connection broken
S.00 No heating demand
S.009 Heating with automatic measuring or adjustment
S.01 Heating: fan starting
S.019 Hot water draw-off with automatic adjustment
S.02 Heating: pump starting
S.029 Hot water cylinder with automatic adjustment
S.03 Heating: burner ignition
S.04 Heating: burner on
S.05 Heating: pump and fan run-on
S.057 Combustion control in emergency mode
S.06 Fan run-on in heating mode
S.07 Pump run-on in heating mode
S.08 Burner off-time in heating mode
S.088 Air purge programme running
S.092 Water circulation self-test
S.093 Flue gas measurement not possible yet
S.10 Hot water demand at the tap
S.108 Purge in progress
S.109 Standby mode active
S.11 Hot water draw-off: fan starting
S.12 Hot water draw-off: pump pre-run
S.13 Hot water draw-off: burner ignition
S.14 Hot water draw-off: burner on
S.15 Hot water draw-off: pump and fan run-on
S.16 Hot water draw-off: fan run-on
S.17 Hot water draw-off: pump run-on
S.199 Automatic filling in progress
S.20 Hot water demand: cylinder or keep-warm
S.21 Hot water cylinder: fan starting
S.22 Hot water cylinder: pump pre-run
S.23 Hot water cylinder: burner ignition
S.24 Hot water cylinder: burner on
S.25 Hot water cylinder: pump and fan run-on
S.26 Hot water cylinder: fan run-on
S.27 Hot water cylinder: pump run-on
S.28 Hot water cylinder: burner off-time
S.30 Heating blocked by the room thermostat
S.31 Summer mode or no demand from the controller
S.32 Waiting: fan speed out of tolerance
S.326 Hydraulic sensor and actuator test
S.328 External pump running permanently
S.33 Waiting: air pressure switch not switched
S.335 Flue blockage test
S.34 Frost protection active
S.36 Controller setpoint below 20 °C
S.37 Waiting: fan fault during operation
S.39 Burner blocked by a contact thermostat
S.40 Comfort safety mode: reduced heating
S.41 Water pressure too high
S.42 Burner blocked by the flue gas flap
S.43 Flow temperature sensor in emergency mode
S.44 Return sensor: comfort safety mode
S.45 Water pressure sensor in emergency mode
S.46 Comfort safety mode: flame lost at minimum load
S.47 Comfort safety mode: flame lost at maximum load
S.48 Comfort safety mode: fan speed deviation
S.51 Flue gas path disturbed
S.52 Flue gas too hot or flue path disturbed
S.53 Waiting time due to water shortage
S.54 Waiting time: water shortage, temperature rising too fast
S.58 Burner output limited
S.59 Water flow too low to start
S.599 The boiler reports a fault
S.60 Waiting time after flame loss
S.76 Water pressure too low, top up
S.85 Water flow too low, maintenance message
S.91 Demonstration mode active
S.95 Voltage check in progress
S.96 Return sensor self-test
S.97 Water pressure sensor self-test
S.98 Flow and return sensor self-test
S.99 System filling in progress