Skip to Content
Repair
Buderus Fault code Buderus
A01

Sensor, hot water or hydraulic setting fault

Breakdown: the boiler is stopped

On a Logano plus KB192i, KB192i.2 or GB212 boiler, A01 is a locking fault: faulty outdoor sensor or hot water sensor, hot water that stays cold, or an unsupported hydraulic configuration, and the number shown next to it (800, 808, 810 or 845) tells which one. On a Logatherm or Bosch Compress heat pump (HMC300, HMC310 or HPC410 control), the number next to it also tells what it is about: hot water thermal disinfection failed (811), defrost fault (5378, and 5526 on the HMC300), indoor and outdoor units that do not match (5522), blocked condensate drain (5450, 5454) or maintenance due (5451) on the HMC300, or, on the HMC310 and HPC410, a message from the outdoor unit about its compressor, its power supply or its refrigerant circuit (5800 to 5829). The heat pump keeps heating as far as possible; if the same fault locks the outdoor unit, code H01 is shown instead.

What you can do

  1. Write down the code shown, the number next to it if there is one, and the boiler model (on the rating plate).
  2. Heat pump with an HMC300 control, number 5450 or 5454: clean the condensate drain (leaves, soil).
  3. Heat pump with an HMC300 control, number 5526: clean the outdoor unit, especially the evaporator.
  4. Heat pump with an HMC300 control, number 5451: the heat pump is due for maintenance; call us to book it.
  5. Reset the boiler once only.
  6. If the code comes back, do not keep trying and do not take anything apart: call us.

Does your boiler show A01?

Repair visit: 360 € excl. VAT (381.60 € incl. 6 % VAT*), first hour included, parts excluded.

* 6 % VAT: work on a private home more than 10 years old, invoiced to a private person. Without a written objection within a month of the invoice, you confirm that these conditions are met; otherwise the VAT is 21 % and the responsibility is yours.

Buderus

Choose a real expert

Ecowatt is an approved Buderus System Partner: factory training in Germany, direct access to spare parts, one contact.

The variants of code A01

The small number shown beside the code tells which.

A01
5378

Outdoor unit defrost fault

Blocking: it retries by itself HMC300, HMC310, HPC410
A01
5450

Z1 Condensate drain blocked

Blocking: it retries by itself HMC300
A01
5451

Heat pump maintenance required

Information: nothing to do HMC300
A01
5454

Z2 Condensate drain blocked

Blocking: it retries by itself HMC300
A01
5522

The indoor and outdoor units do not match

Blocking: it retries by itself HMC300, HMC310, HPC410
A01
5526

Z2 Defrost failed

Breakdown: the boiler is stopped HMC300
A01
5800

Outdoor unit controller restarted

Information: nothing to do HMC310, HPC410
A01
5801

Outdoor unit CAN gateway restarted

Information: nothing to do HMC310, HPC410
A01
5802

No power supply at compressor

Blocking: it retries by itself HMC310, HPC410
A01
5804

Current sensor fault

Blocking: it retries by itself HMC310, HPC410
A01
5806

IPM driver pin fault

Blocking: it retries by itself HMC310, HPC410
A01
5808

AC input zero cross error

Blocking: it retries by itself HMC310, HPC410
A01
5810

Compressor current sensor fault

Blocking: it retries by itself HMC310, HPC410
A01
5812

Compressor driver pin fault

Blocking: it retries by itself HMC310, HPC410
A01
5814

PFC current sensor fault

Blocking: it retries by itself HMC310, HPC410
A01
5816

PFC over current fault

Blocking: it retries by itself HMC310, HPC410
A01
5818

Compressor PFC over current fault

Information: nothing to do HMC310, HPC410
A01
5819

Compressor Overcurrent

Information: nothing to do HMC310, HPC410
A01
5820

Compressor lock undefined driver fault

Blocking: it retries by itself HMC310, HPC410
A01
5822

Low evaporating temperature in cooling

Blocking: it retries by itself HMC310, HPC410
A01
5823

Compressor cannot start

Blocking: it retries by itself HMC310, HPC410
A01
5824

Outdoor unit coil overheating

Information: nothing to do HMC310, HPC410
A01
5825

Low pressure in refrigerant circuit

Blocking: it retries by itself HMC310, HPC410
A01
5826

Outdoor unit heat sink overheating in standby mode

Blocking: it retries by itself HMC310, HPC410
A01
5827

Unspecified outdoor unit fault

Blocking: it retries by itself HMC310, HPC410
A01
5829

High evaporating temperature in cooling (faulty reverse valve)

Blocking: it retries by itself HMC310, HPC410
A01
800

The outdoor temperature sensor is faulty

Breakdown: the boiler is stopped GB212, KB192i, KB192i.2
A01
808

DHW temp. sensor 1 faulty. Deactivate the DHW function if necessary.

Breakdown: the boiler is stopped GB212, KB192i, KB192i.2
A01
810

The domestic hot water stays cold

Breakdown: the boiler is stopped GB212, KB192i, KB192i.2
A01
811

Domestic hot water production: thermal disinfection failed

Blocking: it retries by itself HMC300, HMC310, HPC410
A01
845

The hydraulic configuration is not supported

Breakdown: the boiler is stopped GB212, KB192i, KB192i.2

The boilers that show this code

What our technician checks

  • The connection, cable and mounting of the sensor (outdoor or cylinder)
  • The sensor resistance, compared with its characteristic curve
  • A leak or constant hot water draw, and the cylinder charging pump
  • The configuration of the hot water, heating circuit 1 and the system pump on the module
  • Defrosting: a dirty outdoor unit, thermostats open in the system and the TL2 sensor checked against its table (heat pump, 5378 and 5526)
  • The indoor and outdoor unit combination, and the rotary coding switch setting of a replaced I/O or installer module (5522)
  • The compressor wiring, connections, internal resistances and drive, and the stability of the power supply (5800 to 5827)
  • The refrigerant circuit: isolation valves open, refrigerant leak or blockage, 4-way valve and ICT sensor (5818 to 5829)

The same fault on other boilers

Recent boilers show alone the number older ones show beside the code.

Related codes

From the manufacturer's service manuals for Belgium. Each appliance has its own features: if in doubt, call us.